edgeboard connectors, dual readout www.vishay.com for technical questions, contact: connectors@vishay.com document number: 36003 8 revision: 16-feb-09 eb7d vishay dale electrical specifications current rating: 5 a test voltage between contacts: at sea level: 1800 v rms at 70 000 feet (21 336 meters): 450 v rms insulation resistance: 5000 m minimum at 500 v dc potential contact resistance: 30 mv maximum at rated current (with gold plating) operating temperature: - 55 c to + 125 c humidity: 96 h at 90 % relative humidity at + 40 c, dried at room temperature for 3 h minimum, insulation resistance was greater than 5000 m durability: after 500 cycles of inse rtion and withdrawal of a 0.070" (1.78 mm) thick steel te st gauge, contact resistance less than 0.030 v at 5 a and indi vidual contact retention force when measured with 0.054" (1.37 mm) thick steel test slug greater than ? oz. shock: three 50g shocks in each of 3 mutually perpendicular planes with no loss of continuity vibration: 2 h in each of 3 mutually perpendicular planes, frequency sweep 10 cps to 55 cps at 0.06 double amplitude with no loss of continuity physical specifications contact type: bifurcated bellows number of contacts: 6, 10, 12, 15, 18, 22, 36, 43 per side contact spacing: 0.156" (3.96 mm) center to center card thickness: 0.054" to 0.071" (1.37 mm to 1.80 mm) card slot depth: dual readout = 0.260" (6.60 mm) note ? high temperature burn-in, edgeboard connectors, 0.156" (3.96 mm) center to center are on www.vishay.com/doc?36006 features ? 0.156" c-c x 0.140" grid (3.96 mm x 3.56 mm) ? bifurcated bellows contacts provide 2 flexing contact surfaces to assure positive contact under adverse conditions such as vibration or pc board irregularities ? accepts pc board thickness of 0.054" to 0.071" (1.37 mm to 1.80 mm) ? polarization between contact positions in all sizes. between contact polarization permits polarizing without loss of contact position ? selective gold plating ? polarizing key is reinforced nylon, may be inserted by hand, requires no adhesive. ? protected entry, provided by recessed leading edge of contact, permits the card slot to straighten and align the board before electrical contact is made. prevents damage to contact which might be caused by warped or out of tolerance boards ? recognized under the component program of underwriters laboratories, inc. listed under file e65524, project 77ch3889 applications for use with 0.062" (1.57 mm) printed circuit boards requiring an edgeboard type connector on 0.156" (3.96 mm) centers material specifications body: (standard) glass-filled phenolic per mil-m-14, dark green, flame retardant (ul 94 v-0). (optional - see ordering information) ?1? glass-filled diallyl phtala te per mil-m-14, type sdg-f green, flame retardant (ul 94 v-0) ?3? thermoplastic polyester, glass-filled, black, flame retardant (ul 94 v-0) ?5? thermoplastic polyphenylene sulfied, glass filled, brown, flame retardant (ul 94 v-0) contacts: phosphor bronze polarizing key: glass reinforced nylon, flame retardant (ul 94h-b) contact plating: gold (see ordering information) ordering information eb7 1 d b a 22 sg x a model body material optional body material 1 = diallyl phthalate 3 = glass-filled polyester 5 = glass-filled polyphenylene sulfied = omit number for standard pheniolic dual readout optional contacts beryllium copper copntacts optional available in ?a? and ?e? contact styles only (omit for standard) standard terminal variations a, e, c, or k contacts per side 6, 10, 12, 15, 18, 22, 36, or 43 contact plating sg = selective gold plating (0.00003" (0.000762 mm) minimum thick) on contact area with gold flash on terminal sgf = selective gold plating (0.000010" (0.000254 mm) minimum thick) on contact area with gold flash on terminal. all gold plating over 0.00005" (0.00127 mm) minimum nickel underplate. contact factory for additional plating options. mounting variations polarizing key positions key(s) are located to right of position(s) designated. required only when polarizing keys are to be factory installed
document number: 36003 for technical questions, contact: connectors@vishay.com www.vishay.com revision: 16-feb-09 9 eb7d edgeboard connectors, dual readout vishay dale dimensions in inches (millimeters) section c to c: polarizing key: when ordering polarizi ng keys individually, specify by the model number: pk-7 between contacts. hand insertion tool, tpk-7, provided upon request. # of contact positions per side abdef 6 1.78 (45.21) 1.53 (38.86) 1.22 (30.99) 1.10 (27.94) 0.328 (8.33) 10 2.41 (61.21) 2.16 (54.86) 1.84 (46.74) 1.72 (43.69) 0.328 (8.33) 12 2.72 (69.09) 2.47 (62.74) 2.16 (54.86) 2.04 (51.82) 0.328 (8.33) 15 3.19 (81.03) 2.94 (74.68) 2.62 (66.55) 2.50 (63.50) 0.328 (8.33) 18 3.66 (92.96) 3.41 (86.61) 3.09 (78.49) 2.97 (75.44) 0.328 (8.33) 22 4.28 (108.71) 4.03 (102.36) 3.72 (94.49) 3.60 (91.44) 0.328 (8.33) 36 6.53 (165.86) 6.22 (157.99) 5.91 (150.11) 5.78 (146.81) 0.438 (11.13) 43 7.62 (193.55) 7.30 (185.42) 7.00 (177.80) 6.80 (172.72) 0.500 (12.70) c c a b d e 0.062 0.010 (1.57 0.254) r typ. see table for mountin g variations see table for terminal variations 0.156 0.005 (3.96 0.127) non-cumulative 0.250 (6.35) 0.440 (11.1 8 ) 0.030 (0.762) f 0.010 ( 0.254) type ?a? 0.054 to 0.071 (1.37 to 1. 8 0) 0.260 (6.60) depth of card insertion 0.250 (6.35) types ?c? and ?k? 0.054 to 0.071 (1.37 to 1. 8 0) 0.260 (6.60) depth of card insertion 0.140 (3.56) 0.02 8 (0.711) 0.245 (6.22) 0.230 (5. 8 4)
www.vishay.com for technical questions, contact: connectors@vishay.com document number: 36003 10 revision: 16-feb-09 eb7d vishay dale edgeboard connectors, dual readout mounting variations in inches (millimeters) terminal variations in inches (millimeters) type g c 0.125 0.015 (3.18 0.381) k 0.200 0.015 (5.08 0.381) type ?v? clearance hole 0.250 (6.35) ref. 0.142 (3.61) dia. type ?vi? clearance hole no mountin g pad 0.250 (6.35) ref. 0.142 (3.61) dia. 0.220 (5.59) ref. type ?w? no mountin g flan g e 0.010 (0.254) 0.000 (0.000) type ?x? clearance hole 0.250 (6.35) ref. 0.12 8 (3.25) dia. type ?xi? clearance hole no mountin g pad 0.250 (6.35) ref. 0.220 (5.59) ref. 0.12 8 (3.25) dia. type ?y? threaded insert 0.250 (6.35) ref. 0.21 8 (5.54) ref. 4-40 unc-2b type ?z? floatin g bushin g radial float 0.047 (1.19) note: o v erall b ody length increased b y 0.060 (1.52) 0.250 [6.35] dia. 0.250 (6.35) ref. 0.116 (2.95) dia. 0.270 (6. 8 6) type ?a? pierced to fit 3, #22 awg wires 0.0 8 6 x 0.00 8 (2.1 8 x 0.203) 0.220 0.015 (5.59 0.3 8 1) type ?c? and ?k? solder dip to fit 0.051 (1.30), min. throu g h hole g see table 0.140 0.015 (3.56 0.3 8 1) type ?e? card extender 0.200 0.015 (5.0 8 0.3 8 1) 0.100 (2.54) 0.050 (1.27) 120 typ. 15 typ. 0.0 8 6 (2.1 8 ) uses type ?a? contact
legal disclaimer notice www.vishay.com vishay revision: 02-oct-12 1 document number: 91000 disclaimer all product, product specifications and data are subject to change without notice to improve reliability, function or design or otherwise. vishay intertechnology, inc., its affiliates, agents, and employee s, and all persons acting on it s or their behalf (collectivel y, vishay), disclaim any and all liability for any errors, inaccuracies or incompleteness contained in any datasheet or in any o ther disclosure relating to any product. vishay makes no warranty, repres entation or guarantee regarding the suitabilit y of the products for any particular purpose or the continuing production of any product. to the maximum extent permitted by applicable law, vi shay disclaims (i) any and all liability arising out of the application or use of any product, (ii) any and all liability, including without limitation specia l, consequential or incidental damages, and (iii) any and all i mplied warranties, including warra nties of fitness for particular purpose, non-infringement and merchantability. statements regarding the suitability of products for certain type s of applications are based on vishays knowledge of typical requirements that are often placed on vishay products in generic applications. such statements are not binding statements about the suitability of products for a particular application. it is the customers responsib ility to validate that a particu lar product with the properties descri bed in the product specification is suitable fo r use in a particular application. parameters provided in datasheets and/or specification s may vary in different applications an d performance may vary over time. all operating parameters, including typical pa rameters, must be validated for each customer application by the customers technical experts. product specifications do not expand or otherwise modify vish ays terms and condit ions of purchase, including but not limited to the warranty expressed therein. except as expressly indicate d in writing, vishay products are not designed for use in medical, life-saving, or life-sustaining applications or for any other application in which the failure of the vi shay product could result in personal injury or death. customers using or selling vishay products not expressly indicated for use in such applications do so at their own risk. pleas e contact authorized vishay personnel to ob tain written terms and conditions regarding products designed for such applications. no license, express or implied, by estoppel or otherwise, to any intellectual prope rty rights is granted by this document or by any conduct of vishay. product names and markings noted herein may be trad emarks of their respective owners. material category policy vishay intertechnology, inc. hereby certi fies that all its products that are id entified as rohs-compliant fulfill the definitions and restrictions defined under directive 2011/65/eu of the euro pean parliament and of the council of june 8, 2011 on the restriction of the use of certain hazardous substances in electrical and electronic equipment (eee) - recast, unless otherwis e specified as non-compliant. please note that some vishay documentation may still make reference to rohs directive 2002/95/ ec. we confirm that all the products identified as being compliant to directive 2002 /95/ec conform to directive 2011/65/eu. vishay intertechnology, inc. hereby certifi es that all its products that are identified as ha logen-free follow halogen-free requirements as per jedec js709a stan dards. please note that some vishay documentation may still make reference to the iec 61249-2-21 definition. we co nfirm that all the products identified as being compliant to iec 61249-2-21 conform to jedec js709a standards.
|
